Electric winch EME series
Endless winch for dual direction pulling
This is an epochal endless winch for dual direction pulling equipped with unique functions.
This winch have two drums that rotate the same direction at the same time with several special wire rope groove and two wire rope press rollers attached on the each drum. It provides a stable dual direction pulling power and prevention of wire rope loosing by itself. Users can easily wind a wire rope onto the drum from any portion of the endless wire rope. The winch provides a selection of dual direction pulling in not only one direction but also various directions depending on the purpose of use. In addition, it is also capable of one-way pulling. Thanks to its light weight and small size, users can use it in a wide range of locations.
Examples of using EME winch.
Users can start winding a wire rope from any portion because a side frame is opening and closing type. Therefore, there is no need to process the end of the wire rope.
Several special wire rope grooves that are designed based on an optimum friction factor are inscribed on two drums. This prevents the uneven winding and fits appropriately to the tolerance of wire rope.
The wire rope press rollers in sets of two is installed on each drum, it prevents securely wire rope loosening.
This winch does not require a special wire rope. A commercially available steel core wire rope (Japanese Industrial Standards IWRC 6XFi (29)) can be used on it.
Users can select the control method either of current control or limit control. (Sold separately)
 |
| Model | EME-400 | |
| Frequency | 50Hz | 60Hz |
| Max capacity | 3528N (360kgf) | 2940N (300kgf) |
| Line speed | 5.3 m/min | 6.4 m/min |
| Wire rope diameter | φ8mm (6XFi (29)) | |
| Gear ratio | 1/114 | |
| Motor type | Totally Enclosed Fan Cooled Motor | |
| Output power | 0.4 kW | |
| Number of poles | 4 P | |
| Voltage and current | Three-phase AC200V 50Hz 2.4A | Three-phase AC200V 60Hz 2.1A |
| Voltage and current | Three-phase AC220V 60Hz 2.1A | |
| Brake | Spring Actuated Type Brakes | |
| Duty factor | Continuous | |
| Weight | 77.0 kg | |
| EME-400.pdf |
|
| Model | EME-700 | |
| Frequency | 50Hz | 60Hz |
| Max capacity | 6566N (670kgf) | 5390N (550kgf) |
| Line speed | 5.7 m/min | 6.8 m/min |
| Wire rope diameter | φ9mm (6xFi (29)) | |
| Gear ratio | 1/108 | |
| Motor type | Totally Enclosed Fan Cooled Motor | |
| Motor output | 0.75 kW | |
| Voltage and current | Three-phase AC200V 50Hz 4A | Three-phase AC200V 60Hz 3.5A |
| Voltage and current | Three-phase AC220V 60Hz 3.5A | |
| Brake | Spring Actuated Type Brakes | |
| Duty factor | Continuous | |
| Weight | 82.0 kg | |
| EME-700.pdf |
 |
| Model | EME-1300 | |
| Frequency | 50Hz | 60Hz |
| Max capacity | 12740N (1300kgf) | 10780N (1100kgf) |
| Line speed | 5.33 m/min | 6.38 m/min |
| Wire rope diameter | φ10mm (6xFi (29)) | |
| Gear ratio | 1/134 | |
| Motor type | Totally Enclosed Fan Cooled Motor | |
| Motor output | 1.5 kW | |
| Voltage and current | Three-phase AC200V 50Hz 6.6A | Three-phase AC200V 60Hz 6.1A |
| Voltage and current | Three-phase AC220V 60Hz 5.7A | |
| Brake | Spring Actuated Type Brakes | |
| Duty factor | Continuous | |
| Weight | 120.0 kg | |
| EME-1300.pdf |
It is very easy to wind a wire rope onto the drum.
Conventional endless winches require the use of special wire ropes, and processing the end of the wire rope and winding it from the end when installing it. Maxpull's endless winch supports use of commercially available steel core wire rope, and the wire rope can be wound from any portion onto two opened drums by opening the side frame. 
Remove the bolt of the side frame and open the frame. Loosen each bolt of the press roller located at the end of the right and left, and release the wire rope press roller from the drum.
After winding the wire rope onto the drum, return the side frame and wire press roller to their original positions. Then tighten the bolts , set both ends of the wire rope to the wire stretcher, and take up the slack of the wire rope in using the wire stretcher.
Operate the winch, and rotate the drums in forward and reverse to take up the slack of the wire rope between two drums.
Surely take up the slack of the wire rope in using the wire stretcher.
Use the wire stretcher again to take up the slack of the entire wire rope coming out between the drums.
Control box Deverse automatic dual direction pulling work is possible by the control device. As a standard product, there is a control box with limit operation of reciprocating between two points (Additional cost to the winch body). According to customer requirements, we also offer optional control box that automatic operation can be controlled. Please feel free to contact us.
Inverter control box
Wireless control box
Load calculation formula
Example of using EME electric winch
